Planetary Ball Mill
Ball Mills

Planetary Ball Mill, XQM Series

XQM series planetary ball mills for high-energy laboratory grinding: jar volumes from 1 ml to 5000 ml, speeds up to 800 rpm on the representative model, final fineness below 1 µm, noise ≤65 dB and a 2-year warranty.

Specifications

Series
XQM planetary ball mills
Jar Volume
1–5000 ml (model dependent)
Rotation Speed
100–800 rpm (representative model)
Final Fineness
<1 µm (sub-micron achievable)
Max Feed Size
<10 mm
Jar Materials
Stainless steel, Zirconia, Alumina, Agate, Nylon, PTFE, Tungsten carbide
Control
Digital, programmable (time, speed, run/pause cycles)
Noise
≤65 dB
Warranty
2 years
Power Supply
220V/50Hz or 110V/60Hz (model dependent)

High-energy grinding for the laboratory bench

Some samples do not negotiate. Hard ceramics, alloys for mechanical alloying, geological material, battery research powders — they need impact energy that a tumbling jar cannot deliver, in batch sizes a production mill cannot handle. The XQM planetary ball mill exists for exactly that gap: jars revolve around a central axis while rotating on their own axes in the opposite direction, and the combined forces drive the grinding media into the sample with an intensity no single-motion mill can match. The result is fine and ultrafine grinding down to below 1 µm, with sub-micron results achievable, plus mixing, homogenising and mechanical alloying in the same machine.

Capacity that follows your research, not the other way round

Jar volumes run from 1 ml to 5000 ml across the series, so the same working principle covers a few grams of a precious research sample and a small production batch. Speed on the representative model is adjustable from 100 to 800 rpm, which lets you set the impact energy to the material: hard and brittle samples take the top of the range, while heat-sensitive work runs lower with programmed pause cycles. Feed size is up to 10 mm for pre-crushed material, and the maximum continuous full-load running time is measured in days, not hours — the machine is built for alloying runs and method development, not just quick sample preparation.

Jars and media as one system

Contamination control is decided by the jar and media combination, and the XQM takes the full range: stainless steel for general work, zirconia for high-energy low-contamination grinding, alumina and agate for chemical and analytical work, nylon and PTFE where metal contact is not allowed, and tungsten carbide for the hardest materials. Vacuum jars are available for air-sensitive powders. Tell us your sample and your contamination limits and we will configure the jar and media set with the machine, so the mill arrives as a working system rather than a motor with accessories to argue about later.

Control and working environment

The digital control sets grinding time, speed and run/pause cycles precisely, so a method developed on Monday repeats on Friday. Direction reversal and rest intervals manage heat build-up in long runs. Working noise is held to 65 dB or below, which matters more than brochures admit: a mill that staff avoid switching on is a mill that does not get used. Every machine carries a 2-year warranty.

Who runs an XQM

University and institute laboratories, battery and electronic materials research, ceramics and glass development, geology and mining sample preparation, and enterprise R&D departments that need repeatable fine grinding in small batches. If your current preparation step is the bottleneck between an idea and a measurement, this is the machine that removes it. Send us your material, batch size and target fineness, and we will recommend the model, jar volume and media set for your work.

Continue browsing

More products from the range

Pair it with other media or mills from the same range.

Roller Ball Mill
Ball Mills

Roller Ball Mill, GQM Series

GQM series roller ball mills (jar mills) for laboratory and small-batch grinding and mixing: single, two and four station models, roller speed 60–570 rpm on single-station models, jar loads up to 80 kg, timer 0–999 min.

View product
Stirred Ball Mill
Ball Mills

Stirred Ball Mill, ZLS Series 1–600L

ZLS series stirred ball mills from 1L laboratory units to 600L industrial machines: discharge down to ≤1 µm, 0.37–22 kW, frequency-controlled agitator speed, for nano grinding, dispersion and fine powder production.

View product